Rugged-ridge 3-Inch Bull Bar, Stainless Steel, 07-14 Jeep Wrang Bedienungsanleitung PDF herunterladen

FRONT BULL BAR

2010-12 JEEP WRANGLER 4dr & 2dr

PARTS LIST:

1 3" Bull Bar 2 12-1.75 x 40mm Hex bolts

1 Driver/Left Mounting Bracket 2 12-1.75 x 25mm Hex Bolts

1 Passenger/Right Mounting Bracket 4 12mm x 32mm OD x 3mm Flat Washers

1 Driver/Left Support Bracket 4 12mm Lock Washers

1 Passenger/Right Support Bracket 2 10-1.5mm x 25mm Hex bolts

2 12mm Double Nut plates 4 10mm x 24mm x 2.2mm Flat Washers

2 1/2" x 2” Hex Bolts 2 10mm Lock Washers

2 1/2" Lock Washers 2 10mm Hex Nuts

2 1/2" x 1-1/2" OD x 1/8" Large Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY. CUTTING IS REQUIRED.

2. Remove the plastic splash guard, (Figure 1), from under the front bumper and place it on a clean,

stable work surface.

3. Starting on the driver side, insert (1) 12mm Double Nut Plate, (Figure 2A), into the opening in the

end of the frame crossmember, (Figure 2B). Line up the lower threaded hole in the Nut Plate with

the lower hole in the frame. Select the driver side Mounting Bracket. Bolt the Mounting Bracket to

the side of the crossmember with (1) 12mm x 25mm Hex Bolt, (1) 12mm Flat Washer and (1)

12mm Lock Washer inserted through the lower hole in the Bracket, crossmember and into the

Double Nut Plate, (Figure 3). Leave hardware loose at this time.

4. Next, select the driver side Support Bracket, (Figure 4A). Bolt the Support Bracket to the upper

hole in the Mounting Bracket with (1) 12mm x 40mm Hex Bolt, (1) 12mm Flat Washer and (1)

12mm Lock Washer inserted through the Support Bracket, the upper hole in the Mounting Bracket,

crossmember and into the upper hole in the Nut Plate, (Figure 4B). Snug but do not tighten the

hardware at this time.

5. Repeat Steps 3 – 4 for passenger side Mounting Bracket installation.

6. With help, position the Bull Bar up to the Mounting Brackets. Use the included (2) 1/2" x 2" Hex

Bolts, (2) 1/2" Large Flat Washers and 1/2" Lock Washers to attach the Bull Bar to the Mounting

brackets, (Figure 5). Snug but do not tighten at this time.

Page 1 of 4 1/9/12 (DP)

Driver/Left Mounting

Bracket

Passenger/Right

Mounting Bracket

(2) 12mm Double Nut Plates

Passenger/Right Support Bracket

Driver/Left Support Bracket

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Page 1 of 4 1/9/12 (DP)

FRONT BULL BAR 2010-12 JEEP WRANGLER 4dr & 2dr PARTS LIST: 1 3" Bull Bar 2 12-1.75 x 40mm Hex bolts 1 Driver/Left Mounting Bracket 2 12-

Seite 2

FRONT BULL BAR 2010-12 JEEP WRANGLER 4dr & 2dr7. Bolt the forward end of the Support Brackets onto the outside of the tabs on the Bull Bar with th

Seite 3 - Page 3 of 4 1/9/12 (DP)

FRONT BULL BAR 2010-12 JEEP WRANGLER 4dr & 2drDriver Side Installation PicturedPage 3 of 4 1/9/12 (DP)(1) 10mm x 25mm Hex Bolt(1) 10mm Lock Washer

Seite 4

FRONT BULL BAR 2010-12 JEEP WRANGLER 4dr & 2drPage 4 of 4 1/9/12 (DP)Installation CompleteArea to cut from splash guard illustrated for example on

Kommentare zu diesen Handbüchern

Keine Kommentare

Rugged-ridge 3-Inch Bull Bar, Stainless Steel, 07-14 Jeep Wrang Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rugged-ridge 3-Inch Bull Bar, Stainless Steel, 07-14 Jeep Wrang herunter. Rugged Ridge 3-Inch Bull Bar, Stainless Steel, 07-14 Jeep Wrangler User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rugged-ridge 3-Inch Bull Bar, Stainless Steel, 07-14 Jeep Wrang