Rugged-ridge All Terrain Fender Flare Kit, 87-95 Jeep Wrangler Bedienungsanleitung PDF herunterladen

Rev. 11/11

Page 1 of 4

PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU BEGIN.

YJ: 11630.10

CJ: 11633.10

CJ/YJ ALL TERRAIN FLARE KIT

HARDWARE LIST:

1. M5 Socket Head

Cap Screws-(28)

2. M5 Flat Washers-(28)

3. M5 Flange Nuts-(28)

4. 7mm Rubber Spacers-(22)

5. 13mm Rubber Spacers-(10)

6. Edge Trim-(1 roll)

7. Edge Trim Tool

REQUIRED TOOLS:

1. Drill

2. 1/4” Drill Bit

3. 6mm Allen Wrench

4. 10mm Wrench

5. 5/16” Wrench

6. Felt Tip Marker

7. Scissors

8. Isopropyl Alcohol

*See page 3 for optional painting instructions.

*See page 4 for optional fender trimming for over 33" tires.

Step 1. Remove front factory side markers. Do not discard front markers,

they will be reused. Remove all ares including the front are

extensions. Clean body surface where new ares will mount.

Temporary removal of rear fender well liners may be necessary for

installation of ares.

Step 2. Clean inside mounting lip edge with rubbing alcohol. Install edge

trim as shown in the gure, removing red vinyl tape covering only a

few inches at a time. Do not pull trim while being applied, this may

cause shrinkage after installation.

Step 3. Installing the front ares. Use the front marker light mounting holes

for are alignment. With the marker light temporally installed, align

the bottom of the rear edge of the are with the bottom edge of the

body. Once the are looks aligned, mark the mounting holes with a

felt tip marker. Next remove the marker light and drill the bolt

mounting holes using a 1/4” drill bit. Repeat the same procedures for

both front fender ares.

Step 4. Installing the rear ares. Align the bottom rear edge of the are with

the vertical body panel seam towards the rear corner of the vehicle

and the bottom front edge with the bottom of the body. Once the

are looks aligned, mark the mounting holes with a felt tip marker.

Next remove are and drill the bolt mounting holes using a 1/4” drill

bit. Repeat the same procedures for both rear fender ares.

YJ: 11632.10

1 2 3 4

Inhaltsverzeichnis

Seite 1 - CJ/YJ ALL TERRAIN FLARE KIT

Rev. 11/11Page 1 of 4 SBPLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU BEGIN.YJ: 11630.10CJ: 11633.10CJ/YJ ALL TERRAIN FLARE KITHARDWARE LI

Seite 2

Rev. 11/11Page 2 of 4 SBYJ: 11632.10CJ: 11633.10CJ/YJ ALL TERRAIN FLARE KITStep 6. Install the hardware as shown in the image. First place a wash

Seite 3 - REV 11/13/09

OPTIONAL PAINTING INSTRUCTIONSNOTICE: Do not use any harsh chemicals on flares. Use only plastic approved cleaning chemicals.CUT OUT FLARE PAINT PREPA

Seite 4 - CJ: 11633.10

OPTIONAL FENDER TRIMMING INSTRUCTIONSNote: Image of suggested cut lines are to be used as a guide only. Fenders may be trimmed less

Kommentare zu diesen Handbüchern

Keine Kommentare

Rugged-ridge All Terrain Fender Flare Kit, 87-95 Jeep Wrangler Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rugged-ridge All Terrain Fender Flare Kit, 87-95 Jeep Wrangler herunter. Rugged Ridge All Terrain Fender Flare Kit, 87-95 Jeep Wrangler (YJ) User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rugged-ridge All Terrain Fender Flare Kit, 87-95 Jeep Wrangler