Rugged-ridge Gas Tank Skid Plate, 97-06 Jeep Wrangler (TJ) Bedienungsanleitung PDF herunterladen

Page 1 of 3

NOTE: Perform installation when gas gauge reads

below 1/4 tank. A lighter gas tank will be easier to

manage. Also, have a partner handy to assist with

the removal and installation of the tank.

WARNING: When working near gasoline, always be cautious not to have any heat or ame generating

device as this could result in combustion and cause injury or death. Always keep a re extinguisher handy

when working with combustible uids.

1. Disconnect battery terminals before beginning installation of this product. Disconnect negative terminal

rst making sure not to contact the positive terminal with the tool being used.

2. Remove the gas cap from the vehicle to relieve the pressure inside the

tank. Cut zip ties holding axle vent tubes to the ller hose. To gain access to

these tubes, remove the plastic cover from underneath the rear quarter panel.

Remove the fuel ller assembly by rst removing the 4 screws holding the

ller neck in position. Next, remove the 4 screws holding the plastic bezel.

Save these screws, they will be used to reinstall ller neck. NOTE: Instead of

removing the complete ller assembly, ller and overow hoses can be

removed directly from the tank by loosening the clamps securing them.

3. Some TJ models will have a grounding strap attached to the driver’s

side shock mount. Use a at head screwdriver to remove it. Disconnect the

electrical connector on top of the gas tank by sliding the red clip to the side

and unlocking the connector. Also disconnect the evaporation hose and high

pressure line from the metal tubing at the left front corner of the tank.

NOTE:

Have a bucket and some shop rags handy. Fuel may spill out when

disconnecting fuel lines.

4. Position oor jack centered beneath the gas tank to hold it in place.

Remove the 7 nuts holding the gas tank and the OE skid pan to the vehicle.

Save these nuts as they will be used to reinstall the gas tank. Do not remove

the nuts securing the gas tank to the OE skid pan straps untill the gas tank is

on the ground.

Contents:

1. TJ Gas Tank Skid Plate (1)

97-06 TJ GAS TANK SKID PLATE

18003.22

1 2 3

97-06 TJ GAS TANK SKID PLATE 1

Inhaltsverzeichnis

Seite 1 - 97-06 TJ GAS TANK SKID PLATE

Page 1 of 3NOTE: Perform installation when gas gauge readsbelow 1/4 tank. A lighter gas tank will be easier tomanage. Also, have a partner handy to

Seite 2

Page 2 of 35. Late model jeeps will have the fuel rail connected to the top of the tank. Using the oor jack, lower the gastank approx 3 inches. Un

Seite 3

18003.2297-06 TJ GAS TANK SKID PLATE10. Locate 2 axle vent hoses and zip tie hoses to fuel ller neck. Also,reconnect the grounding strap to the dri

Kommentare zu diesen Handbüchern

Keine Kommentare

Rugged-ridge Gas Tank Skid Plate, 97-06 Jeep Wrangler (TJ) Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rugged-ridge Gas Tank Skid Plate, 97-06 Jeep Wrangler (TJ) herunter. Rugged Ridge Gas Tank Skid Plate, 97-06 Jeep Wrangler (TJ) User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rugged-ridge Gas Tank Skid Plate, 97-06 Jeep Wrangler (TJ)